If the spider arm breaks as a result of rust, you’ll need to replace it. ![]() This arm holds the tub shaft through the drum bearings. Your machine has a spider arm assembly at the back of the inner tub. Click here for detailed steps on how to do this. If you find any cracks or damage to the block, it will need to be replaced. To check if the block is damaged, use your Philips screwdriver to remove the screws holding the top panel. There is a block mounted at the top of the assembly which prevents the machine from shaking excessively. Read this article for steps on how to do this. If the suspension springs are damaged, you’ll need to replace them. You should also ensure that they are properly secured to the cabinet. Inspect the two suspension springs for rust or damage. To check if the suspension springs are damaged, loosen the bolts at the back of the machine holding the top panel, then take the cover off. This ends up causing a lot of problems for your machine. ![]() If one of the springs goes bad, the tub assembly becomes unbalanced. The suspension springs hook the tub assembly onto the cabinet. ![]() Plug your washing machine’s power cord back into the electrical outlet, then try running a spin cycle to see if the issue has been fixed. With your needle-nosed pliers, loop the retaining band around the door gasket. Open your machine’s door and fit the boot seal around the front panel. Snap the top panel onto the front of the cabinet, then tighten the screws at the back using your Philips screwdriver. Set your washing machine upright, then apply the two screws next to the dispenser opening. Carefully tip your washing machine backwards a bit, then tighten the four screws beneath the front panel. With your Philips screwdriver, apply the four screws at the top of the control panel. Lift the front panel and mount it on the cabinet. Once you’ve properly tightened the bolts, plug the wire connectors back into the front panel. Use a 7/16 inch socket wrench to properly tighten the bolts holding the lower and upper counter-weights to the front of the tub assembly. Carefully lift the entire front panel off the cabinet, then unplug the two electrical connectors from it. Remove the support from underneath your washer, then set the appliance back onto its feet. Remove the four screws at the bottom of the front panel. Place a block underneath the front panel. Get someone to help you tip your washing machine backwards and support it. Peel the door boot seal off the front panel. Wedge a flat-blade screwdriver underneath the metal wire around the door boot seal, then pry the wire off (ensure that you do not accidentally puncture the seal. Remove the four screws at the top of the front panel. Use your Philips screwdriver to take out the two screws next to the detergent dispenser. Pull the detergent drawer out of the dispenser, then press the button to release it from the housing. Lift the top panel off the cabinet, then set it aside. Take out the screws at the back of the machine holding the top panel to the cabinet using a Philips screwdriver. With someone else to assist you, move the washing machine forwards a bit to get more working space. In order to prevent any chances of electrocution, make sure to disconnect your washing machine from the outlet before starting this procedure. Here are the steps you’ll need to take to tighten the counter-weights… If your Electrolux washing machine is going out of balance, the counter-weights at the front of the tub may have gotten loose. To replace damaged shock absorbers in your in your Electrolux washing machine, read this article. Good shock absorbers should have little resistance. If the shock absorbers move freely when pushed and pulled, then they have gone bad. Take out the front and rear panels of your machine and inspect the shock absorbers for cracks or damage. If your washing machine is going out of balance, it could be that the shock absorbers have gone bad. ![]() Your Electrolux washing machine has four shock absorbers mounted at the bottom of the tub. Set the washing machine back onto the floor, then make sure the appliance is properly balanced using a spirit level tool. Use a spanner wrench to adjust the legs under the machine as needed. If you notice a lot of movement, it indicates that the legs are uneven.Ĭarefully tip the washing machine backwards, then get someone to help you support it. Try rocking the machine forwards and backwards a bit to see how much it moves. If Electrolux washing machine is unbalanced, the first thing you should do is check to ensure that it sits on an even surface. If your Electrolux washing machine is unbalanced, here are the issues to look for… 1. Drum Bearings Have Gone Bad How To Balance Electrolux Washer - Solution How To Balance Electrolux Washer - Solution.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |